Front Suspension & Steering Categories
Front Suspension & Steering
Showing 1–24 of 134 results
-
Front Frame Kits, S&W Made Parts
2″x3″ Strut Front Frame & Crossmember
Part# 36-500
SW’s strut front frame package is designed to simplify installation for the do-it-yourselfer.The base frame package features mandrel formed 2″ x 3″ frame rails, rear lower control arm mounts, a fully welded rack pinion crossmember with front lower control arm mounts and a front subframe support package to tie the frame rails to the roll cage. . Complete installation requires the use of an upper strut mounting kit. This kit can be used with any eye or stud mount Strange strut package.
Note: picture shows struts and rack installed
SKU: 36-500 -
Control Arms, Mopar Dodge Plymouth Bolt-on Parts
62-72 MOPAR B-BODY / 70-74 E-BODY LOWER A-ARM KIT QA-1 #52308
Control Arms, Mopar Dodge Plymouth Bolt-on Parts62-72 MOPAR B-BODY / 70-74 E-BODY LOWER A-ARM KIT QA-1 #52308
Part# 35-52308
62-72 MOPAR B-BODY / 70-74 E-BODY LOWER A-ARM KIT QA-1 # 52308, CONTROL ARMS ARE DIRECT BOLT-IN ON THE FACTORY K-MEMBER KIT INCLUDED BUSHINGS PIVOT ARMS AND NUTS RECOMMENDED FOR 1962-70 B-BODY WITH NO SWAY BAR OR E-BODY SWAY BAR AND QA1 K-MEMBER.  FOR 70-74  MOPAR E-BODY WILL WORK WITH E-BODY SWAY BAR AND 1971-72 B-BODY SWAY BAR
SKU: 35-52308 -
Control Arms, Mopar Dodge Plymouth Bolt-on Parts
62-72 MOPAR B-BODY & 70-74 E-BODY UPPER A-ARM KIT
Part# 35-52305
62-72 MOPAR B-BODY/70-74 E-BODY UPPER A-ARM KIT QA-1 #52305, TUBULAR CONSTRUCTION, BLACK POWDER COAT POLYURETHANE INNER PIVOT BUSHINGS CONTROL ARMS INCREASE CASTER BY APPROXIMATELY 3-DEGREES EACH SET COMES WITH BALL JOINTS FITS 62-72 MOPAR B-BODY AND 70-74 MOPAR E-BODY
SKU: 35-52305 -
Control Arms, Mopar Dodge Plymouth Bolt-on Parts
64-72 MOPAR A-BODY / 73-76 A-BODY LOWER A-ARM KIT QA-1 #52307
Control Arms, Mopar Dodge Plymouth Bolt-on Parts64-72 MOPAR A-BODY / 73-76 A-BODY LOWER A-ARM KIT QA-1 #52307
Part# 35-52307
64-72 MOPAR A-BODY / 73-76 A-BODY LOWER A-ARM KIT QA-1 # 52307 DIRECT BOLT-IN ON FACTORY K-MEMBER INCLUDED BUSHINGS, PIVOT ARMS AND NUTS WORKS WITH THE 1964-66 A-BODY WITH NO SWAY BAR AND 1967-73 A-BODY WITH THE 1973-76 SWAY BAR OR “FLAT BAR”
SKU: 35-52307 -
Control Arms, Mopar Dodge Plymouth Bolt-on Parts
64-72 MOPAR A-BODY UPPER A-ARM KIT QA-1 #52303
Part# 35-52303
64-72 MOPAR A-BODY UPPER A-ARM KIT, QA-1 # 52303, TUBULAR CONSTRUCTION, BLACK POWDER COAT POLYURETHANE INNER PIVOT BUSHINGS CONTROL ARMS INCREASE CASTER BY APPROXIMATELY 3-DEGREES EACH SET COMES WITH BALL JOINTS
SKU: 35-52303 -
K-Member, Front Suspension & Rear Suspension Packages, S&W Made Parts, Racks
67-69 Camaro & 68-74 Nova Rack & Pinion Mounting Kit
K-Member, Front Suspension & Rear Suspension Packages, S&W Made Parts, Racks67-69 Camaro & 68-74 Nova Rack & Pinion Mounting Kit
Part# 35-371
Converts stock rear steer to rack & pinion front steer. removal of stock lower control arm crossmember required. Replacement removable tubular crossmember under engine included. Also includes rack pinion mounting bracket, billet aluminum pinto rack mount clamp, tie rods, diagonal brace gussets and crossmember cap off plates with integral tie down loops and hardware. Cutting, fitting welding required.
Note” pinto rack 35-042 and 35-078 aluminum steering arms not included
SKU: 35-371 -
Control Arms, Mopar Dodge Plymouth Bolt-on Parts
73-76 MOPAR A-BODY UPPER A-ARM KIT QA-1 #52301
Part# 35-52301
73-76 MOPAR A-BODY UPPER A-ARM KIT QA-1 # 52301, TUBULAR CONSTRUCTION, BLACK POWDER COAT POLYURETHANE INNER PIVOT BUSHINGS CONTROL ARMS INCREASE CASTER BY APPROXIMATELY 3-DEGREES EACH SET COMES WITH BALL JOINTS THIS CONTROL ARM IS ONLY FOR FACTORY CARS AND ANY A-BODY THAT WAS SWAPPED TO DISC BRAKES WITH FACTORY PARTS. (LARGE BALL JOINTS)
SKU: 35-52301 -
-
Racks
74-78 Mustang II Manual Rack/Pinion 3″ Narrower Than Stock
Part#35-037-3
Flaming River 74-78 Mustang II manual rack pinion 3″ narrower than stock , 13″ Center to center on rack mounts 4.15 turns lock to lock rack travel 5.25″Pivot= 21.5 center to center Flaming River Rack #1502-3×3 manual rack overall length is 42″ , used in 36-400-3 package
SKU: 35-037-3 -
S&W Made Parts, Front End Kit Replacement Parts
A-Arm Package – Mustang II – Lower with hardware
Part#36-402
Lower control arms-black powder coated. All necessary harware to bolt to frame also includes hardware to mount shock to frame Used in  36-400 package 36-400-3 package replacement bushings #36-402A , NOTE: Ball joints not included but can be ordeered seperately  #36-003
SKU: 36-402 -
Front Frame Kits
A-Arm Frame 52-3/16 Hub to Hub Kit
Part# 36-400-6KIT
52-3/16″ hub to hub
2 x 3 x 120 wall frame rails , x-member, 3/16″thick suspension brackets, Includes frame rails with a-arm brackets and shock support brackets welded on. Rack crossmember with rack mount welded on. Frame “X” brace, pre-notched to fit 52-3/16″ hub to hub, 24″ outside 20″ inside. Overall length 100″. 88″ from spindle centerline to end of rail. Front crossmember must be welded to frame rails buy installer.
Kit includes:
Frame rails with welded brackets
Front crossmember with welded rack mount brackets
Upper & lower tubular control arms with ball joints
Mustang II spindles
Flaming River rack with mounts
Single adjustable coil over shocks and springs
Tie rods
Front supports
SKU: 36-400-6KIT -
Front Frame Kits
A-Arm Frame 55-3/16 Hub to Hub Kit
Part# 36-400-3KIT
55-3/16″ hub to hub
2 x 3 x 120 wall frame rails , x-member, 3/16″thick suspension brackets, Includes frame rails with a-arm brackets and shock support brackets welded on. Rack crossmember with rack mount welded on. Frame “X” brace, pre-notched to fit 55-3/16″ hub to hub, 27″ outside 23″ inside. Overall length 100″. 88″ from spindle centerline to end of rail. Front crossmember must be welded to frame rails buy installer.
Kit includes:
Frame rails with welded brackets
Front crossmember with welded rack mount brackets
Upper & lower tubular control arms with ball joints
Mustang II spindles
Flaming River rack with mounts
Single adjustable coil over shocks and springs
Tie rods
Front supports
SKU: 36-400-3KIT -
Front Frame Kits
A-Arm Frame 58-3/16 Hub to Hub Kit
Part# 36-400KIT
58-3/16″ hub to hub
2 x 3 x 120 wall frame rails , x-member, 3/16″thick suspension brackets, Includes frame rails with a-arm brackets and shock support brackets welded on. Rack crossmember with rack mount welded on. Frame “X” brace, pre-notched to fit 58-3/16″ hub to hub, 30″ outside 26″ inside. Overall length 100″. 88″ from spindle centerline to end of rail. Front crossmember must be welded to frame rails buy installer.
Kit includes:
Frame rails with welded brackets
Front crossmember with welded rack mount brackets
Upper & lower tubular control arms with ball joints
Mustang II spindles
Flaming River rack with mounts
Single adjustable coil over shocks and springs
Tie rods
Front supports
SKU: 36-400KIT -
Front Frame Kits, S&W Made Parts
A-Arm Frame Rails 52-3/16 Hub to Hub
Part# 36-400-6
52-3/16″ hub to hub
2 x 3 x 120 wall frame rails , x-member, 3/16″thick suspension brackets, Includes frame rails with a-arm brackets and shock support brackets welded on. Rack crossmember with rack mount welded on. Frame “X” brace, pre-notched to fit 52-3/16″ hub to hub, 24″ outside 20″ inside. Overall length 100″. 88″ from spindle centerline to end of rail. Front crossmember must be welded to frame rails buy installer.
Used In 36-400-6 KIT
SKU: 36-400-6 -
Front Frame Kits, S&W Made Parts
A-Arm Frame Rails 55-3/16 Hub to Hub
Part# 36-400-3
55-3/16″ hub to hub
2 x 3 x 120 wall frame rails , x-member, 3/16″thick suspension brackets, Includes frame rails with a-arm brackets and shock support brackets welded on. Rack crossmember with rack mount welded on. Frame “X” brace, pre-notched to fit 55-3/16″ hub to hub, 27″ outside 23″ inside. Overall length 100″. 88″ from spindle centerline to end of rail. Front crossmember must be welded to frame rails buy installer.
Used In 36-400-3 KIT
SKU: 36-400-3 -
Front Frame Kits, S&W Made Parts
A-Arm Frame Rails 58-3/16 Hub to Hub
Part# 36-400
58-3/16″ hub to hub
2 x 3 x 120 wall frame rails , x-member, 3/16″thick suspension brackets, Includes frame rails with a-arm brackets and shock support brackets welded on. Rack crossmember with rack mount welded on. Frame “X” brace, pre-notched to fit 58-3/16″ hub to hub, 30″ outside 26″ inside. Overall length 100″. 88″ from spindle centerline to end of rail. Front crossmember must be welded to frame rails buy installer.
Used In 36-400KIT
SKU: 36-400 -
-
