| Weight | 75 lbs |
|---|---|
| Dimensions | 48 × 12 × 12 in |
S&W Made Parts, Rear Axle Housings, Stock Replacement/Bolt In
2005-2014 Mustang Bolt In 9″ Housing Stock Width
Part# 45-447
2005-2014 Mustang Bolt In 9″ Housing, Axle face to axle face 65-1/4″, center pinion, 9″ Bolt in replacement for stock 8.8″ rear axle housing. Requires late model big Ford brakes. Shock control arm brackets in stock location. Lower control arm bracket feature addition holes for suspension adjustment. Late model big Ford housing end accepts 3.150″ axle bearing ? Requires aftermarket axles. No provision for factory anti roll bar. WILL NOT accept stock mustang brakes.
Use 45-044 kit to mount factory brakes
Note: for 2″ narrower, use part# 45-448
$1,099.95
Product Q&A Ask a Question
Success!
Question Added Successfully
Sort by
-
This product has no questions.
You may also like…
Related products
-
Stock Replacement/Bolt In
78-87 G Body Malibu, Grand National Complete 9″ Ford Big Bearing Bolt In Rear
Stock Replacement/Bolt In78-87 G Body Malibu, Grand National Complete 9″ Ford Big Bearing Bolt In Rear
Part# 45-619
JOHNS INDUSTRIES 78-87 G BODY MALIBU, GRAND NATIONAL COMPLETE 9″FORD BIG BEARING BOLT IN REAR: COMES WITH ALL NEW U.S. MADE HOUSING, NEW 31 SPLINE HIGH PERFORMANCE AXLES, SPRING PERCHES, BRACKETS AND TABS, TRU TRAC THIRD MEMBER WITH DESIRED RATIO, SUPER LIGHT IRON NODULAR CASE, NEW PINION YOKE, BEARINGS, STUDS, ALL FASTENERS, AXLE SEALS, HOUSING VENT.AND FORD 10″ DRUM BRAKES
SKU: 45-619 -
Stock Replacement/Bolt In
64-77 Chevelle & Monte Carlo Complete 9″ Ford Big Bearing Bolt In Rear
Part# 45-618
JOHN INDUSTRIES 64-77 CHEVELLE, MONTE CARLO COMPLETE 9″FORD BIG BEARING BOLT IN REAR: COMES WITH ALL NEW U.S. MADE HOUSING, NEW 31 SPLINE HIGH PERFORMANCE AXLES, SPRING PERCHES, BRACKETS AND TABS, TRU TRAC THIRD MEMBER WITH DESIRED RATIO, SUPER LIGHT IRON NODULAR CASE, NEW PINION YOKE, BEARINGS, STUDS, ALL FASTENERS, AXLE SEALS, HOUSING VENT.AND FORD 10″ DRUM BRAKES
SKU: 45-618 -
Chassis & Blueprints, Blueprints, S&W Made Parts
Blueprint – 225″ Advanced ET Dragster with Soild Mount Rear
Chassis & Blueprints, Blueprints, S&W Made PartsBlueprint – 225″ Advanced ET Dragster with Soild Mount Rear
Part# 05-001-AET-BP
Assembly blueprint with cut list for 225″ wheelbase ADVANCED ET dragster with solid mount rear. Meets SFI spec 2.5B for rear engine dragster 6.00 to 7.49 seconds .. NOTE – assembling a drag race vehicle form a blue print is not for beginners and should only be attempted by a skilled and experienced fabricator
SKU: 05-001-AET-BP -
S&W Made Parts, Rear Axle Housings, Stock Replacement/Bolt In
2005-2014 Mustang Fabricated 9″ Ford Housing 2″ Narrowed
S&W Made Parts, Rear Axle Housings, Stock Replacement/Bolt In2005-2014 Mustang Fabricated 9″ Ford Housing 2″ Narrowed
Part# 45-447FAB
2″ narrower than stock. Replaces stock 8.8 rear housing, uses late model big Ford ends (45-1137), shock control arm brackets in stock location, lower control arm brackets have additional holes, center pinion, 58-1/4″ housing end to housing end, 63-1/4″ axle flange to axle flange, for upper control arm hardware use 45-445H. Has brace mounts for anti-roll bar kit 40-708K
If using factory brakes, need to purchase 45-044 kit-
SKU: 45-448FAB