| Weight | 75 lbs |
|---|---|
| Dimensions | 51 × 7 × 5 in |
Bolt-in Rear Housings, Stock Replacement/Bolt In, S&W Made Parts
Bolt In 9″ Ford Housing for 82-92 Camaro Stock Width
Part# 45-450
Same width as stock, 56-1/4″ housing end to housing end, 61-3/4″ axle face to axle face, (1/2″ pinion off-set), uses GM housing ends with 3.15 bearing. Uses after market brakes. Brackets are in stock locations, lower control arm brackets have additional mounting holes. Adjustable weight jacker spring pad. Works with 40-619 or 40-619CM torque arm and 40-600 or 40-600CM frame connectors
$818.25
Upgrades
Product Q&A Ask a Question
Success!
Question Added Successfully
Sort by
-
This product has no questions.
Related products
-
Stock Replacement/Bolt In
58-64 Full Size Chevy Complete 9″ Ford Big Bearing Bolt In Rear
Part# 45-622
JOHNS INDUSTRIES COMPLETE 9″FORD BIG BEARING BOLT IN REAR 58-64 FULL SIZE CHEVY, COMES WITH ALL NEW U.S. MADE HOUSING, NEW 31 SPLINE HIGH PERFORMANCE AXLES, SPRING PERCHES, BRACKETS, AND TABS, TRU TRAC THIRD MEMBER, DESIRED RATIO, SUPER LIGHT IRON NODULAR CASE, NEW PINION YOKE, BEARINGS, STUDS, ALL FASTENERS, AXLE SEALS, AND HOUSING VENT.W/ FORD 10″ DRUM BRAKES, FITS 58-64 FULL SIZE CHEVY
SKU: 45-622 -
Stock Replacement/Bolt In
2005-Newer Mustang Complete 9″ Ford Big Bearing Bolt In Rear
Part# 45-623
JOHNS INDUSTRIES 2005-NEWER MUSTANG COMPLETE 9″FORD BIG BEARING BOLT IN REAR: COMES WITH ALL NEW U.S. MADE HOUSINING, NEW 31 SPLINE HIGH PERFORMANCE AXLES, SPRING PERCHES, BRACKETS AND TABS, TRU TRAC THIRD MEMBER WITH DESIRED RATIO, SUPER LIGHT IRON NODULAR CASE, NEW PINION YOKE, BEARINGS, STUDS, ALL FASTENERS, AXLE SEALS, HOUSING VENT.AND FORD 10″ DRUM BRAKES
SKU: 45-623 -
S&W Made Parts, Chassis & Blueprints, Dragster, Altered, & Funny Car
21″ Wide, 225″ Wheelbase Dragster Chassis Kit- Solid Mount Strange Rear
S&W Made Parts, Chassis & Blueprints, Dragster, Altered, & Funny Car21″ Wide, 225″ Wheelbase Dragster Chassis Kit- Solid Mount Strange Rear
Part# 05-001S-AET
225″ WHEEL BASE, 21″ SHOULDER HOOP, ALL TUBING IS CHROME MOLY, NOTCHED AND BENT, INCLUDED STRANGE ALUMINUM REAR MOUNTING PLATES, A-ARM FRONT END WITH KING PIN BOSSES, FULL MID MOTOR PLATE FRONT MOTOR MOUNT PLATES FOR BIG BLOCK CHEVY, MEETS SFI SPEC 2.5 FOR 6.00 – 7.49 SECONDS
SKU: 05-001S-AET -
S&W Made Parts, Chassis & Blueprints, Blueprints
Blueprint – 225″ Dragster with Solid Mount Rear
Part# 05-001-BP
Assembly blueprint with cut list for 225″ wheelbase dragster with solid mount rear. Meets SFI spec for rear engine dragster 6.00 seconds and slower. NOTE – assembling a drag race vehicle form a blue print is not for beginners and should only be attempted by a skilled and experienced fabricator
SKU: 05-001-BP
